Precision and Magnetic Tools Manufacturers
MRM – 475, 475 H, 575, 575H, 676, 676H, 856, 856H, 876, 876H, 976, 976H
The - Blocks have a total of three magnetic surfaces. Top and bottom each with 90- degree v – angle and end surface opposite from switch. All three magnetic surfaces as well as the two sides are carefully ground. Their accuracy for flatness, parallelism and square ness is within 0.005 mm or 0.0002 inches for all work, which requires accurate positioning.
When turned ‘ON ‘ all three magnetic surfaces are activated simultaneously. The permanent magnet holds the work firmly in the V and the block holds itself firmly on a ferrous surface. Coolants or other fluids cannot damage the magnetic system, being shielded from penetration of moisture.
Request a Quote
Hardened V Blocks with Clamps
The V – Blocks have two V – angles of different size to take parts of varying dimensions.
By means of the clamp the Work can be held tight in the block. The accuracy of the vee block/100mm is within 0.005 mm.
Request a Quote
Permanent Magnetic Chucks
This permanent magnetic chuck guarantees outstanding performance and reliability. The rigid assembly of these chucks result in accurate grinding and milling.
The selected pole spacing ensures the maximum possible grip on a wide section of work-pieces. Using an additional top plate can accommodate all types, sizes and shapes of work-pieces. The magnet used is ‘NdFeB’. This magnet is very powerful than 'AlNiCo' magnet.
Under ideal conditions the test result show that the holding power/Cu.Inch is 55Kg., which is much bigger than ‘AlNiCo’ magnetic chuck.
Request a Quote
Universal Surface Gauges
Universal Surface Gauge has many desirable features and is designed for wide range of uses, which are supplied in four sizes.
The base is made from case hardened steel, ground on bottom and at one end. The Fine adjustment feature makes it possible to obtain quick and accurate settings.
This adjustment is made by a knurled thumbscrew, which is located at the end of the rocker. The rocker runs the 2/3 the length of the base and pivots against a stiff spring located at the rear end of the base.
Request a Quote
Magnetic Base Indicator Holders SRD- 101
A powerful permanent magnetic type base holds firmly any steel or iron surface horizontally, vertically or up-side down, thus eliminating time spent on clamping indicator to machine.
A convenient large diameter push button turns magnetic pull ‘on’ or ‘ off ‘ for quick one hand set up and removal of base. The base and two sides are energized for attachment to flat surfaces and a V slot facilitates gripping on curved surfaces.
An improved model with a versatile clamping assembly which can hold any plunger type of dial indicator available in Metric as well as English System and can easily hold any lever type of dial indicators with 6 mm, 8 mm i.e, 1 / 4” and 5 / 16
Request a Quote
Magnetic Base KM- 525
A powerful permanent magnetic type base holds firmly to any steel or iron surface, horizontally, vertically or up side down, this eliminating time spent on clamping indicator to machine.
When magnet is turned ‘ON ‘ by the lever, the base and two sides are energized for attachment on flat surfaces and a ‘ V ‘ slot facilitates gripping of the cylindrical shafts.
Request a Quote
Magnetic Base With Articulated Arm Magnetic Base Manufacturer
A model range 3 – D measurement, articulated stand with unlimited adjustment. A mechanical central clamping system with one lock mechanism (All joint locks).
Maintenance free and has micro fine adjustment for dial gauges and feelers. A well – planned model, guarantees individual field of application.
Request a Quote
Heavy Duty Magnetic Base KM - 725
A powerful permanent magnetic type base holds to any steel or iron surface - horizontally, vertically or up side down, thus eliminating time spent on clamping indicator to machine.
When magnet is turned 'ON' by the knob, the base remains firmly clamped in any desired position. The base and two sided energized for attachment on flat surfaces and a 'V slot facilitates gripping of the stand of shafts with a diameter range of 20 to 120 mm.
The unique clamping which can hold dial indicator 8 mm or 5/16" stem diameter simple and quick setting is obtained by a new clamping of the extension arm, which guarantees absolutely rigid clamping even with moderate tightening. Magnet should be turned "OFF" when not in use.
Request a Quote
Roller Bearing V Blocks Vee Block Manufacturers
Used for checking heavy and odd shaped round jobs.
Perfectly matched pair having accuracy 0.005 mm
Included angle of rollers is 90°
Standard bearings are used which are replaceable
Jobs don’t get damaged due to bearing on top
Request a Quote
Heavy Duty Multicoil Electro-Magnetic Chucks
Strong Magnetic Field to hold the work piece strongly.
Used for holding on surface grinding machine.
Chuck is tested for earth terminal test, waterproof test, temperature rise test, & demagnetizing tests.
Provided with variable supply to vary power, which helps in aligning & removing of warp ages of thin jobs.
Work holding device for surface grinding machines, each pole is having separate coil, as such very strong & even magnetic flux is generated.
Request a QuoteElectro-Perm Magnetic Chucks
"KUMAUN" introduces Electro-perm Magnetic Chucks for heavy duty milling machine. These chucks ensure high magnetic and mechanical performance. This chuck is "COLD" device, as no internal wear or deformation resulting from moving internal parts.
Electro-perm Magnetic Chucks do not consume electrical power except for the very short period of activation or deactivation of the working surface. Once fixed to the machine table EPM chucks are as stable as machine.
EPM chucks are economical for operation and maintenance. Magnetic clamping system is most powerful. Chucks are switched ON & OFF by simple electrical pulse. A variable output from 20% to 100 % is controlled from push button unit.
In operating condition no power supply is necessary for holding work pieces. So no risk when power fails.
The de-magnetization cycle of chuck eliminates possible residual magnetism in work piece, therefore easy release for high alloy steel parts. EPM chuck is designed for heavy-duty operation such as milling cut of 3 to 6 mm depth at recommended speed & feed.